Laboratory Incharge : Ms. Meenakshi Mataray

Technical Staff : Mr. Ashutosh Kumar

Objective:

To provide the students with a basic foundation for analysis, design and testing of power electronics converters by simulation and experimentation.

Major Equipment

• Single phase half wave rectifier kit
• Single phase full wave rectifier kit
• Single phase mid-point cyclo converter kit
• Characteristic of SCR
• Single phase AC voltage regulator
• Triggering of MOSFET, IGBT kit
• IGBT bridge Inverter
• IGBT chopper circuit

Laboratory Incharge : Ms. Sadaf Naqvi

Technical Staff : Mr. Vijay Kumar Rai

Objective:

To introduce students the methods to solve and analyse networks using provided resources in the laboratory.

Major Equipment

• Superposition Theorem verification kit
• Thevenin’s, Norton’s, Maximum power transfer theorem verification kit
• Tellegen’s theorem verification kit
• RLC network kit
• z and h parameter kit
• ABCD parameter kit
• Interconnection of networks kit
• Low pass and High pass filters

Laboratory Incharge : Ms. Sadaf Naqvi

Technical Staff : Mr. Vijay Kumar Rai

Objective:

To instruct students various concepts of control systems having industrial applications and enhance their practical exposure.

Major Equipment

• P, PI, PID controller kit
• RTD kit
• DC position control system
• Synchro transmitter and receiver kit
• AC servomotor
• Servo voltage stabiliser
• Lag, lead, lag-lead compensator kit
• DC motor in open and closed loop configuration

Laboratory Incharge : Ms. Nisha Parveen

Technical Staff : Mr. Ashutosh Kumar

Objective:

To familiarize students with the operation of various instrumentation technologies used in engineering fields.

Major Equipment

• LVDT kit
• Proximity sensor kit
• Strain Gauge based on load cell kit
• Strain Gauge based on water level kit
• P, PI, PID controller kit
• RTD kit
• Thermocouple kit
• Anemometer kit

Laboratory Incharge : Mr. Vikas Tripathi

Technical Staff : Mr. Suresh Giri

Objective:

To accustom students with the fundamentals of power transmission and distribution system and the various protection schemes used.

Major Equipment

• Oil testing set
• Cable fault locator
• Mho, Impedance and Reactance relays
• IDMT over current relay
• Percentage differential relay
• Line and ground fault detectors
• Panel for determination of Direct axis and Quadrature axis reactance
• Panel for studying Ferranti effect

Laboratory Incharge : Mr. Vikas Singh Negi, Ms. Rashmi Jain

Technical Staff : Mr. Atul Goel

Objective:

To impart deep knowledge about the working of various electrical machines seen in daily life as well as in industries, by giving students as much physical exposure as possible.

Major Equipment

• DC shunt motor and generator with panel
• Dc series motor with panel
• DC compound motor and generator with panel
• Panel for synchronisation of 3 phase alternator
• 3 phase induction motor with panel
• 1 phase induction motor with panel
• Panel for speed control of 3 phase induction motor by V/f method
• Panel for 3 phase synchronous machine
• Panel for Scott connection
• Panel for V-curve of 3 phase synchronous machine
• Panel for Hopkinson test for DC shunt machine
• Panel for speed control of DC shunt motor by Ward-Leonard method
• Panel for alternator and DC shunt motor
• Rectifier panel AC to DC

Laboratory Incharge : Mr. S. P. Bihari, Mr. Bhupendra Sehgal

Technical Staff : Mr. Ashish Rastogi, Mr. Munesh Sharma

Objective:

To forge basic concepts of electricity and magnetism in students with a practical view point and prepare them for the future challenges in engineering.

Major Equipment

• KVL and KCL verification kit
• Superposition, Thevenin, Norton, Maximum Power Transfer Theorem verification kit
• RLC parameter calculation kit
• RLC Resonance kit
• Power factor calculation kit
• Single phase transformer panel
• Two wattmeter method panel
• 3 phase induction motor panel

Laboratory Incharge : Mr. Vikas Singh Negi

Technical Staff : Mr. Ashutosh Kumar

Objective:

To teach students various software modules of their interest and to make them accustomed with the recent trends in industries.

Software Used

• MATLAB
• Scilab (Open Source)

Laboratory Incharge : Mr. Vikas Singh Negi

Technical Staff : Mr. Ashutosh Kumar

Objective:

To familiarize students with the various simulation techniques used in industries to make them more resourceful as an engineer.

Software Used

• MATLAB
• Simulink
• Scilab (Open Source)

Laboratory Incharge : Mr. R. N. Chaubey

Technical Staff : Mr. Suresh Giri

Objective:

To impart hand on exposure and experience of the various electrical equipments and on site conditions while catering to sponsored research projects, modernization & development.

Major Equipment

• Major Equipment
• Major Equipment
• Bread board, Components (R,L,C)
• Cut out view of various electrical machines and equipment
• Project Kits: Transmission line surveillance robot, Wireless power transfer, Multilevel parking, etc